Hello guys. Is everyone tired of shitty oils? Is everyone tired of people gatekeeping sources and the sources being out of stock all the time? Just cook it urself nigga. Whenever u fucking want and you know what you are putting in it. You know you arent injecting straight fucking piss since you are the creator. Anyways lets get started.

First things first. always use a brew calculator so you don’t fuck up the math.

I recommend https://dinfarcalc.vercel.app

Recipe for 10ml 200mg/ml Test cyp.

Testosterone Cypionate powder: (-) grams (watever the calculator shows)

Benzyl Alcohol (BA): 2% (watever the calculator shows)

Benzyl Benzoate (BB): 18% (watever the calculator shows)

MCT Oil (watever the calculator shows)

Equipment Needed:

Warning (Make sure you got a vial top closer. If you dont , dont worry. Buy vials that are already closed.) (theres 2 types of vials. Closed already and the ones you gotta close yourself.)

0.22μm syringe filters

18g needles + 5ml syringes

Two 50ml glass beakers

Hot plate with magnetic stirrer (recommended)

Caulking gun (for filtering)

Milligram scale

Empty sterile vials

Air filter (highly recommended)

This is the source where you can get these equipments. (free source leak too while most people make you pay for them so thank me)

https://www.medical-and-lab-supplies.com

Step by Step Brewing Process.

Sterilization

Turn on your air filter in the room 30 minutes before starting.

Place your beakers, syringes, needles, and vials in a hot steam bath for 10-15 minutes, then put them in the oven at 350°F (175°C) for 60 minutes to fully sterilize.

Weighing and Mixing

Weigh out grams of Test Cyp powder and put it in one beaker. (Amazon milligram scale , also look at the brewing calculator for how much grams you need)

In the second beaker, add your MCT oil and begin heating it on the hotplate to 50-60°C for 10 minutes.

Dissolving the Powder

Warning (when you see the test cyp powder disolved , thats when its time to add BB and BA.)

Once the MCT is warm, draw it up with a 5ml syringe (no needle needed) and slowly add it to the beaker containing the Test Cyp powder.

Place the beaker on the hotplate with stirring. (the test cyp beaker that now has the mct oil in it) Start at 70°C and gradually increase the temperature to 104°C over 10-15 minutes (example is 70°C and wait 10 minutes and up to 85. then wait 10 minutes and up to 104.)

Adding Solvents

Once the powder is fully dissolved, add BA and BB. (check brew calculator again how much you need) Stir for another 5 minutes until everything is clear.

Filtering

Get 1 18g needle and put it inside the top like a cross. Basically like this. (the picture has 2 because one of them is the one you will filter with) Get a syringe (no needle) and pull all the oil (the test cyp) in. Then add your 0.22 Filter on it. After adding the filter on the syringe. You add the 18g needle on the filter. Like this. The other step is to put it as the picture i showed above (as a cross)and put the needle in it. Then get a caulking gun and put the syringe in the caulking gun.

Using a caulking gun + 0.22μm filter (u can get this froma amazon), push the oil into your sterile 10ml vial. (This will be a nice forearm workout. Just take your time.)

Go slow to avoid blowing out the filter.

The final results.

Guys this will take months for some people to perfect but its fucking worth it long term trust me.

blameqt on discord if theres any questions. I recommend leaving it in the fridge after cooking to see if it will crash. then leaving it outside for weeks on room temp. Do this because you just started cooking, you arent a pro yet. Your test might crystalize in ur ass if u dont do this. You can stop doing this after you are sure that you are a pro at cooking.

Lets say it crystalizes what do we do?

Buy ziploc bags and put the vial in it. and put it in very hot water (can be a big glass and super hot sink water.) Leave it there and watch the crystalized test dissolve.